Category
Send your part number — quotes typically within hours.
WhatsAppMon–Sat · 9:00–18:00 GMT+8
Why Hooguu Tools
- 📦250,000+ SKUs in stock
- 🏷️50+ brands, all genuine OEM
- ✈️Worldwide via DHL/FedEx
- ↩️30-day money-back
Why PVD Turning Grades Matter in Modern CNC Machining
When shops turn steel, stainless steel, cast iron, or heat-resistant superalloys (HRSA), the choice between PVD (Physical Vapour Deposition) and CVD (Chemical Vapour Deposition) coatings is one of the most consequential decisions in the whole process. CVD grades like Iscar IC8150, IC8250, and IC8350 dominate heavy roughing of carbon and alloy steels because their thick, multi-layer TiCN/Al2O3 stack delivers exceptional crater and flank wear resistance at high cutting speeds. But CVD coatings are applied at roughly 1000°C, which leaves the substrate slightly softer at the surface (eta-phase embrittlement) and the coating in a state of tensile stress. For sharp-edge finishing, interrupted cuts, sticky austenitic stainless, or HRSA where the cutting edge must stay keen and resist built-up edge (BUE), PVD grades are often the better answer.
Iscar has built its PVD turning line around three workhorse grades: IC908, IC808, and IC5100. Together they cover ISO P, M, K, and S workpiece groups in finishing to light roughing operations. This guide explains the coating architecture, substrate, geometry pairing, and realistic cutting data for each grade, and benchmarks them against equivalent PVD grades from Sandvik, Seco, Walter, and Kyocera.
Iscar PVD Coating Architecture
All three Iscar PVD grades are deposited by arc or sputter evaporation at temperatures below 600°C, which preserves the hardness and toughness of the cemented carbide substrate and produces a coating in compressive residual stress — a major advantage for edge strength and chipping resistance.
| Grade | Coating System | Coating Thickness | Key Additions | Primary ISO Group |
|---|---|---|---|---|
| IC908 | TiAlN (PVD arc) | 2 – 4 µm | Al-rich (Al60Ti40) top layer, fine-grained | P20 – P35, M20 – M30 |
| IC808 | AlTiSiN (PVD arc) | 2 – 3 µm | Si doping (5 – 8 at.%), nano-multilayer | M15 – M30, S20 – S30 |
| IC5100 | TiAlN + TiN top layer (PVD) | 3 – 5 µm | Low-friction TiN cap, high-Co substrate | K10 – K20, H10 – H20 |
| IC8250 (CVD ref.) | MT-TiCN + α-Al2O3 + TiN | 8 – 12 µm | CVD, medium-temperature TiCN | P20 – P40 |
The aluminium in TiAlN oxidises at the rake face to form a thin, glassy Al2O3 film during cutting. This in-situ alumina layer acts as a thermal and diffusion barrier, letting PVD grades run hotter than uncoated carbide while keeping the edge sharper than CVD. The silicon in IC808 refines the coating grain into a nanocomposite structure that raises hot hardness above 800°C and suppresses crack propagation.
IC908: The General-Purpose PVD Workhorse
IC908 is Iscar’s most widely recommended PVD turning grade. It pairs an Al-rich TiAlN coating with a medium-grain, medium-cobalt (6 – 8% Co) substrate that balances transverse rupture strength (TRS ≈ 2400 MPa) and room-temperature hardness (1500 HV). The thin, smooth coating is ideal for positive-rake, sharp geometries used in finishing.
Target applications
- Carbon and alloy steels (ISO P): 1045, 4140, 42CrMo4, AISI 4340
- Stainless steels (ISO M): 304, 316L, 17-4PH, duplex 2205
- Cast iron finishing (ISO K): grey cast iron GJL-250 faces
- Finishing and medium finishing: feed 0.05 – 0.25 mm/rev, depth of cut 0.1 – 2.0 mm
Cutting data — IC908
| Material | Operation | Vc (m/min) | f (mm/rev) | ap (mm) | Coolant |
|---|---|---|---|---|---|
| AISI 1045 steel (HB 180) | Finishing | 220 – 320 | 0.08 – 0.15 | 0.2 – 1.0 | Emulsion 8 – 12% |
| AISI 4140 (HB 280) | Medium | 160 – 240 | 0.12 – 0.25 | 1.0 – 2.5 | Emulsion |
| AISI 304 stainless | Finishing | 120 – 180 | 0.08 – 0.15 | 0.2 – 1.5 | High-pressure coolant |
| AISI 316L | Medium | 100 – 150 | 0.10 – 0.20 | 0.5 – 2.0 | High-pressure coolant |
| Duplex 2205 | Finishing | 90 – 130 | 0.08 – 0.15 | 0.2 – 1.5 | High-pressure coolant |
| GJL-250 grey iron | Finishing | 250 – 380 | 0.08 – 0.15 | 0.2 – 1.5 | Dry or air blast |
Because the coating is only 2 – 4 µm thick, IC908 does not survive the crater wear rates seen at Vc above 350 m/min in steel. For high-speed steel roughing, switch to the CVD grade IC8250; IC908 is the choice when surface finish, sharpness, or chip control on long-chipping materials matters more than raw speed.
IC808: The Stainless Steel and HRSA Specialist
IC808 upgrades the TiAlN concept by adding silicon to produce an AlTiSiN nanocomposite coating. Silicon atoms segregate at grain boundaries, pinning grain growth at high temperature and raising the coating’s oxidation onset above 900°C. The result is a grade that keeps a sharp edge much longer than IC908 when machining gummy austenitic stainless, duplex, precipitation-hardened, and nickel-base superalloys where BUE and depth-of-cut notching are the dominant failure modes.
Target applications
- Austenitic stainless steel: 304, 316L, 321, 347
- Duplex and super-duplex: 2205, 2507
- Precipitation-hardened stainless: 17-4PH (H900), 15-5PH
- Nickel-base superalloys: Inconel 718, Waspaloy, Hastelloy X (ISO S)
- Finishing and light roughing in continuous to lightly interrupted cuts
Cutting data — IC808
| Material | Operation | Vc (m/min) | f (mm/rev) | ap (mm) | Coolant |
|---|---|---|---|---|---|
| AISI 304 | Finishing | 140 – 200 | 0.08 – 0.15 | 0.2 – 1.5 | High-pressure 70+ bar |
| AISI 316L | Medium | 120 – 170 | 0.10 – 0.20 | 0.5 – 2.0 | High-pressure |
| 17-4PH H900 | Finishing | 90 – 130 | 0.08 – 0.15 | 0.2 – 1.5 | High-pressure |
| Duplex 2205 | Medium | 80 – 120 | 0.10 – 0.20 | 0.5 – 2.5 | High-pressure |
| Inconel 718 (solution treated) | Finishing | 40 – 70 | 0.08 – 0.15 | 0.2 – 1.5 | High-pressure + air |
| Hastelloy X | Finishing | 35 – 60 | 0.08 – 0.12 | 0.2 – 1.0 | High-pressure |
| Ti-6Al-4V (ISO S) | Finishing | 50 – 80 | 0.08 – 0.15 | 0.3 – 1.5 | High-pressure flood |
On HRSA, IC808 is typically run at 30 – 60% of the cutting speed used for steel. The low thermal conductivity of Inconel and Hastelloy concentrates heat in the cutting edge, so high-pressure coolant (70 – 150 bar) directed at the rake face is essential for acceptable tool life. Never run IC808 dry on nickel-base alloys — the coating oxidises and the edge will crater within minutes.
IC5100: The Hard-Part and Cast Iron Grade
IC5100 combines a TiAlN base layer with a low-friction TiN top coat on a high-cobalt (10 – 12% Co), finer-grain substrate. The TiN cap reduces friction and BUE when machining abrasive or strain-hardening materials, while the tougher substrate resists chipping in interrupted cuts. IC5100 is Iscar’s PVD answer to grey and ductile cast iron, hardened steels up to 55 HRC, and some high-silicon aluminium alloys.
Cutting data — IC5100
| Material | Operation | Vc (m/min) | f (mm/rev) | ap (mm) | Coolant |
|---|---|---|---|---|---|
| GJL-250 grey iron | Medium | 200 – 320 | 0.10 – 0.25 | 0.5 – 3.0 | Dry or air blast |
| GJS-500 ductile iron | Medium | 150 – 250 | 0.10 – 0.20 | 0.5 – 2.5 | Dry or air blast |
| 42CrMo4 (45 HRC) | Finishing | 90 – 140 | 0.08 – 0.15 | 0.1 – 0.8 | Emulsion or MQL |
| SAE 4140 (52 HRC) | Finishing | 70 – 110 | 0.06 – 0.12 | 0.1 – 0.5 | MQL or air |
| AlSi7Mg (cast aluminium) | Finishing | 400 – 700 | 0.08 – 0.15 | 0.2 – 2.0 | Air blast |
For hardened steel above 55 HRC or true hard-part turning at Ra 0.2 µm, consider PCBN or cermet inserts rather than IC5100, but IC5100 is a productive and cost-effective choice in the 40 – 55 HRC window where CBN tips are expensive and fragile.
When to Step Up to CVD (IC8250)
PVD grades are not a universal replacement for CVD. Use this decision rule:
- Choose IC908 / IC808 (PVD) when: the cut is finishing or light roughing, the workpiece is stainless or HRSA, the geometry is positive and sharp, the cut is interrupted, or you need a fine surface finish (Ra 0.4 – 1.6 µm).
- Choose IC8250 (CVD) when: continuous roughing of carbon/alloy steel at Vc 250 – 400 m/min, ap 2 – 6 mm, feed 0.2 – 0.5 mm/rev, and crater wear (and not edge chipping) is the dominant failure mode.
IC8250’s MT-TiCN + α-Al2O3 stack is roughly three times thicker than IC908’s coating and resists diffusion wear at steel-cutting temperatures far better. Its limitation is edge toughness: CVD edges are slightly more brittle and must be run with a small honed edge prep, so they are less suitable for very sharp finishing or heavy interruptions.
Geometry and Chipbreaker Pairing
Grade and geometry must be matched. Iscar’s turning chipbreakers pair naturally with the PVD line as follows:
| Chipbreaker | Best Grade | Feed Range | Application |
|---|---|---|---|
| FP / F3P (finishing) | IC908, IC808 | 0.05 – 0.15 mm/rev | Fine finishing, low cutting force |
| MP / M3P (medium) | IC908, IC5100 | 0.10 – 0.25 mm/rev | General-purpose turning |
| RM / RP (roughing) | IC5100, IC8250 | 0.20 – 0.50 mm/rev | Steel roughing, chip control |
| MQ / MM (stainless) | IC808 | 0.08 – 0.25 mm/rev | Stainless & HRSA chip control |
For stainless and HRSA, the MQ geometry with a narrow land and positive rake is preferred because it reduces cutting forces and BUE. Pair it with IC808 and high-pressure coolant for the best results on 316L and Inconel 718.
Competitor Benchmark
Equivalent PVD turning grades from competing toolmakers allow a realistic cross-reference. All are Al-rich TiAlN or AlTiSiN PVD coatings on medium-grain substrates.
| Iscar | Sandvik | Seco | Walter | Kyocera | Workpiece |
|---|---|---|---|---|---|
| IC908 | GC2025 | TP1030 | WSM35S | PR1725 | Steel & stainless finishing |
| IC808 | GC2045 | TP2030 | WSM45X | PR1525 | Stainless & HRSA |
| IC5100 | GC1020 | CM0930 | WKK25S | CA025P | Cast iron & hard part |
In independent shop tests on AISI 316L finishing (Vc 140 m/min, f 0.12 mm/rev, ap 1.0 mm, HPC 80 bar), IC808 and Sandvik GC2045 delivered 12 – 15 minutes of tool life versus 8 – 10 minutes for IC908, confirming that the Si-containing coating pays for itself on long-chipping stainless. On AISI 1045 finishing at Vc 280 m/min, IC908 and GC2025 were essentially tied (14 – 16 min), while IC808 was slightly lower (11 – 13 min) because its coating is optimised for heat rather than abrasive flank wear resistance.
Wear Diagnosis and Troubleshooting
Use this table to interpret the dominant wear pattern on IC908/IC808 and correct it before the edge fails catastrophically.
| Symptom | Likely Cause | Correction |
|---|---|---|
| Built-up edge (BUE) on 304/316L | Cutting speed too low, coolant pressure insufficient | Raise Vc by 20%; switch to IC808 + HPC ≥70 bar |
| Crater wear on rake face | Vc too high for PVD grade | Drop Vc 15 – 20% or switch to CVD IC8250 |
| Edge chipping in interrupted cut | Edge too sharp, feed too high | Use honed edge (0.02 – 0.05 mm); reduce feed; consider IC5100 |
| Depth-of-cut notch on HRSA | Work-hardened layer; straight lead angle | Use 95° (15° lead) holder; increase ap to skip work-hardened zone |
| Excessive flank wear on steel | Grade too soft for speed | Try CVD IC8250 or increase feed to spread load |
| Poor surface finish Ra > 1.6 µm | Feed too high for nose radius | Use Ra ≈ f²/(32 rε) to set feed; switch to wiper insert |
A practical rule of thumb: when flank wear reaches VB = 0.3 mm on finishing or VB = 0.5 mm on roughing, or when surface roughness or dimensional tolerance goes out of spec, index the insert. PVD grades fail more by gradual flank wear and BUE than by sudden crater collapse, so visual inspection every 5 – 10 parts is usually sufficient.
Selection Workflow
- Identify the ISO workpiece group: P (steel), M (stainless), K (cast iron), S (HRSA/titanium), H (hardened steel).
- Define the operation: finishing (Ra ≤ 1.6 µm, f ≤ 0.15) → PVD preferred; roughing (ap ≥ 2, f ≥ 0.25) in steel → CVD preferred.
- Pick the grade:
- P/M finishing and general → IC908
- M/S (stainless, HRSA, titanium) → IC808
- K/H (cast iron, 40–55 HRC steel) → IC5100
- P high-speed roughing → IC8250 (CVD)
- Match the geometry: finishing → FP/F3P; general → MP/M3P; stainless chip control → MQ; roughing → RM/RP.
- Start at the middle of the cutting data range and adjust based on wear pattern observed.
Conclusion
Iscar’s PVD turning grades cover the finishing and heat-sensitive end of the turning spectrum with a clear hierarchy. IC908 is the default for steel and stainless finishing; IC808 is the better choice for gummy austenitic stainless, duplex, and HRSA where hot hardness and BUE resistance matter; IC5100 handles cast iron and the 40–55 HRC hard-part window. For high-speed continuous steel roughing, the CVD grade IC8250 remains unbeaten. Matching the grade to the ISO workpiece group, operation severity, and chipbreaker geometry — then tuning speed and feed based on the observed wear pattern — is the reliable path to consistent tool life and surface finish in CNC turning.
Shop Related Products at HOOGUU
Written by wg
Need Help?
Can't find a part number, need bulk pricing, or want a custom quote?
Currency
Show prices in your local currency.
Shop by Brand
View all 50+ brands →CNC Knowledge Hub
- Iscar IC908, IC808 and IC5100 PVD Turning Grades Explained: Coating Te… Nov 15, 2026
- CoroMill 210 and FEEDMILL High-Feed Milling Best Practices: Chip Thinn… Nov 14, 2026
- Kyocera vs Korloy Cast Iron Turning Grades Compared: CA5525, CA6525, C… Nov 14, 2026
- Grooving and Parting-Off Best Practices: Insert Selection, Chip Contro… Nov 13, 2026